CL4790 Series
Learn more and compare with similar parts on the family page.


Antenna Options
Dipole; RPSMA jack (female)
Antenna Type
Up to 32 in U.S.
Chipset (Wireless)
TI CC1010
Data Rate
76.8 Kbps fixed
Dimension (Height - mm)
35.56 mm
Dimension (Length - mm)
111.76 mm
Dimension (Width - mm)
68.58 mm
Frequency Range (Max)
928 MHz
Frequency Range (Min)
902 MHz
Input Power
7Vdc to 18Vdc
Logical Interfaces
Network Architecture
Connexlink Setup Wizard
Operating Humidity
10 to 90% (non-condensing)
Output Power
Conducted: 743mW. EIRP: 1486mW
Power Consumption
400 mA @ 12V DC
Product Type
Cable Replacement System
FHSS Wireless Protocol
Max. 1500 feet (450 m) indoors; Max. 20 miles (32 km) line-of-sight
Receive Sensitivity
-100 dBm
System Architecture
Proprietary RF (9xx MHz)
Transmit Power (Max)
+ 28 dBm
< 6 oz (< 170 g)
Wireless Specification
900 MHz FHSS

Buy Now

Distributor Part In Stock Region Buy
DigiKey CL4790-1000-485 207 North America Buy Now
Mouser CL4790-1000-485 58 North America Buy Now
Mouser CL4790-1000-485 58 North America Buy Now
DigiKey CL4790-1000-485 4 North America Buy Now
Avnet CL4790-1000-485 0 North America Buy Now
Future Electronics CL4790-1000-485 0 North America Buy Now
Future Electronics CL4790-1000-485 0 North America Buy Now
Symmetry Electronics CL4790-1000-485 0 North America Buy Now


How do I return my ConnexLink Radio, AC4490/AC4790, RM024, LT1110 radio to its default settings?

In order to return the radio to its default EEPROM settings it is necessary to load a previously saved file containing the default settings to the Configuration Utility and write the changes to the radio. If you did not save the default settings to a file, prior to changing the settings, please contact Laird Support through the Support Portal to request a file with the default settings for the purpose of restoring the radio to its default configuration.

The "Show Default" settings view in the Laird Configuration and Test Utility should NEVER be written to the radio, as these are for reference ONLY. Writing these to the radio can result in corrupting the radio to a point where it can become unrecoverable. After viewing the "Show Default" settings, the radio settings should always be READ again, prior to writing any changes to the radio, to prevent this from occurring.

Is an adapter required to connect the ConnexLink units (CL4490-1000-485 | CL4790-1000-485 | CL4490-1000-232 | CL4790-1000-232 | CL4490-1000-PRO) to a PC to enable me to configure them with Laird's configuration software?

Configuring the RS232 and PRO variants of the Laird ConnexLink units (CL4490-1000-232, CL4790-1000-232, or CL4490-1000-PRO) requires connecting to a Windows PC via an RS232 serial port. As most newer computers no longer have an RS232 serial port available, an RS232-to-USB adapter would be required to connect the unit to the PC. Customers have reported success with the following RS232-to-USB adapters:

  • FTDI RS232-to-USB Model: UC232R-10
  • Tripp-Lite Keyspan RS232-to-USB Model: USA-19HS

Configuring the RS485 variants of the ConnexLink Units (CL4490-1000-485 or CL4790-1000-485) requires an RS485 adapter to connect to a Windows PC either via an RS232 serial port, or via USB. Customers have reported success with the following:

  • B&B Electronics RS485-to-RS232 adapter Model: 485SD9TB combined with one of the above mentioned RS232-to-USB adapters
  • ULinx RS485-to-USB adapter Model: 485USBTB-2W

The Laird Configuration & Test Utility Software along with the Laird Configuration and Test Utility Software - RAMP Modules User Guide, is available to download from the CL4490 and CL4790 Product Pages.

What is difference between AC4490/AC4790 product part numbers that end with -01, -02, -03?

The -01, -02, -03 at the end of the part number signifies the version of firmware loaded to the module.
These firmware versions are Regionally significant and apply certified for the regions listed:



Part Number Certification Region
AC4490-1000M-01 FCC IC/North America
AC4490-1000M-02* RCM/C-Tick* Australia
AC4490LR-1000M-01 Long Range FCC/IC North America
AC4490LR-1000M-02* RCM/C-Tick* Australia*
AC4490LR-1000M-03 Anatel Brazil
AC4790-1000M-01 FCC/IC North America
AC4790-1000M-02* RCM/C-Tick* Australia*
AC4790LR-1000M-01 FCC/IC North America
AC4790LR-1000M-02* RCM/C-Tick* Australia*
CL4490-1000-232-01 (RS232) FCC/IC North America
CL4490-1000-232-03 (RS232) Anatel Brazil
CL4490-1000-232-SP-01 (RS232 - Starter Pack - Includes 2 units) FCC/IC North America
CL4490-1000-485-03 (RS485) Anatel Brazil
CL4490-1000-485-01 (RS485) FCC/IC North America
CL4490-1000-485-SP-01 (RS485 - Starter Pack - Includes 2 units) FCC/IC North America

*RMC/C-Tick Certified modules/ConnexLink must be purchased through Tekdis as they hold the certification.